收藏本站
L. S. INPUT, 30 CPS MAX.
The CUB7W accepts most machine control voltage signals. The input accepts
AC (50/60 Hz) or DC control voltages from 10 to 300 V at count speeds up to
30 cps. The unit counts on the positive going edge of the input signal.
WARNING : Any lead may be at hazardous live input potential.
External wiring and devices connected to the unit must be rated
the same as applied signal input voltage and be properly isolated
from Class 2 or SELV circuitry.
INSTALLATION ENVIRONMENT
The unit should be installed in a location that does not exceed the maximum
operating temperature and provides good air circulation. Placing the unit near
devices that generate excessive heat should be avoided.
The bezel should be cleaned only with a soft cloth and neutral soap product.
Do NOT use solvents.
Continuous exposure to direct sunlight may accelerate the aging process of
the bezel.
Do not use tools of any kind (screwdrivers, pens, pencils, etc.) to operate
the keypad of the unit.
Installation
The CUB7 series of products meets NEMA 4X/IP65 requirements for
indoor use, when properly installed. The units are intended to be mounted into
an enclosed panel. The viewing window and reset button are factory sealed for
a washdown environment. A sponge rubber gasket and mounting clip are
provided for installing the unit in the panel cut-out.
The following procedure assures proper installation:
1. Cut panel opening to specified dimensions. Remove burrs and clean around
panel opening.
2. Carefully remove and discard the center section of the gasket. Slide the
panel gasket over the rear of the unit to the back of the bezel. Insert the
mounting screws onto both sides of mounting clip. Tip of screw should
NOT project from hole in mounting clip.
3. Install CUB7 unit through the panel cut-out until front bezel flange contacts
the panel.
4. Slide the mounting clip over the rear of the unit until the clip is against the
back of the panel. The mounting clip has latching features which engage
into mating features on the CUB7 housing.
BATTERY INSTALLATION
1. Remove all power to the unit before removing battery cover.
2. To remove battery cover, push upward in the direction of the arrow on rear
cover (See drawing at right), until the cover unlatches. Pull cover straight
out from unit to fully remove.
3. Remove old battery* and replace with an RLC battery (BNL10000).
Observe proper polarity when replacing battery as shown in drawing.
4. Replace cover. The battery cover is keyed so that it cannot be placed upside
down. The arrow on the rear of the cover should point toward the top of the
CUB7 series when properly installed
* - Dispose of properly.
WARNING : Lithium battery may explode if incinerated.
3
Note: It is necessary to hold the unit in place when sliding mounting clip
into position.
5. Alternately tighten each screw to ensure uniform gasket pressure.
Visually inspect the front panel gasket. The gasket should be compressed to
about 75 to 80% of its original thickness. If not, gradually turn mounting
screws to further compress gasket.
6. If gasket is not adequately compressed and the mounting screws can no
longer be turned, loosen mounting screws, and check that mounting clip is
latched as close as possible to the panel.
7. Repeat from step #5 for tightening mounting screws.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
550-2504 LED 5MM VERT HI EFF ORANGE PCMNT
550-2407 LED 5MM RT ANG HI EFF RED PCMNT
7Q-26.000MBS-T OSC VCTCXO 26.000 MHZ 3.3V SMD
550-2404 LED 5MM VERT HI EFF RED PC MNT
550-2307 LED 5MM RT ANG HI EFF YEL PCMNT
550-2304 LED 5MM VERT HI EFF YELL PC MNT
550-2207 LED 5MM RT ANG HI EFF GRN PC MNT
550-2204 LED 5MM VERT HI EFF GREEN PC MNT
相关代理商/技术参数
CUB7W010 功能描述:COUNTER 8-DIGIT YEL BKLT VOLT-IN RoHS:是 类别:工业控制，仪表 >> 计数器 系列:CUB7 其它有关文件:Declaration of Conformity 标准包装:1 系列:99766 计数速率:25Hz 数字/字母数:5 输入类型:机电式脉冲 输出类型:- 电源电压:24V 显示器类型:十进制拨轮
CUB7W020 功能描述:COUNTER 8-DIGIT RED BKLT VOLT-IN RoHS:是 类别:工业控制，仪表 >> 计数器 系列:CUB7 其它有关文件:Declaration of Conformity 标准包装:1 系列:99766 计数速率:25Hz 数字/字母数:5 输入类型:机电式脉冲 输出类型:- 电源电压:24V 显示器类型:十进制拨轮
CUB8A-1 制造商:IMO Precision Controls Ltd 功能描述:INVERTER 1 PHASE 1.5KW 制造商:IMO Precision Controls Ltd 功能描述:AC MOTOR DRIVER; Supply Voltage Min:200VAC; Supply Voltage Max:240VAC; No. of Phases:Single; Power Rating:1.5kW; Output Voltage Max:230V; External Depth:151mm; Frequency Range:0.1 to 400Hz; Input Current:16.4A; Output Current:8A ;RoHS Compliant: Yes
CUB8A-1 制造商:IMO Precision Controls Ltd 功能描述:INDICATOR M/BLOCK LED 24AC RED
CUB9A-4 制造商:IMO Precision Controls Ltd 功能描述:INVERTER 3 PHASE 4KW 制造商:IMO Precision Controls Ltd 功能描述:AC MOTOR DRIVER; Supply Voltage Min:380VAC; Supply Voltage Max:480VAC; No. of Phases:Three; Power Rating:4kW; Output Voltage Max:415V; External Depth:141mm; Frequency Range:0.1 to 400Hz; Input Current:13A; Output Current:9A ;RoHS Compliant: Yes
CUB9A-4 制造商:IMO Precision Controls Ltd 功能描述:INVERTER 3 PHASE 0.75KW
CUB9A-4 制造商:IMO Precision Controls Ltd 功能描述:INVERTER 3 PHASE 4.0KW ((NS))
CUBAMUBAM28020033UM-10E 制造商:GRAND-TEK TECHNOLOGY 功能描述:USB CABLE ASSY A-A 1M